CPB Modbus RTU Technical Manual

Pin assignment

Overview

CPB3



CPB6



CPB15



X1 — voltage supply and motor

CPB3

Connector: Würth Elektronik 61301211121

Pin Name Description/function
1 GND
2 BN_OUT B\ (stepper motor)
3 BN_OUT B\ (stepper motor)
4 B_OUT B (stepper motor) or W (BLDC)
5 B_OUT B (stepper motor) or W (BLDC)
6 AN_OUT A\ (stepper motor) or V (BLDC)
7 AN_OUT A\ (stepper motor) or V (BLDC)
8 A_OUT A (stepper motor) or U (BLDC)
9 A_OUT A (stepper motor) or U (BLDC)
10 +UB 12 - 57.6 V DC
11 +UB 12 - 57.6 V DC
12 GND

CPB6

Connector: Würth Elektronik 61302421121

Pin Name Description/function
1 GND
2 GND
3 BN_OUT B\ (stepper motor)
4 BN_OUT B\ (stepper motor)
5 BN_OUT B\ (stepper motor)
6 BN_OUT B\ (stepper motor)
7 B_OUT B (stepper motor) or W (BLDC)
8 B_OUT B (stepper motor) or W (BLDC)
9 B_OUT B (stepper motor) or W (BLDC)
10 B_OUT B (stepper motor) or W (BLDC)
11 AN_OUT A\ (stepper motor) or V (BLDC)
12 AN_OUT A\ (stepper motor) or V (BLDC)
13 AN_OUT A\ (stepper motor) or V (BLDC)
14 AN_OUT A\ (stepper motor) or V (BLDC)
15 A_OUT A (stepper motor) or U (BLDC)
16 A_OUT A (stepper motor) or U (BLDC)
17 A_OUT A (stepper motor) or U (BLDC)
18 A_OUT A (stepper motor) or U (BLDC)
19 +UB 12 - 57.6 V DC
20 +UB 12 - 57.6 V DC
21 +UB 12 - 57.6 V DC
22 +UB 12 - 57.6 V DC
23 GND
24 GND

CP15

Connector: Samtec MPT-06-6.30-01-L-V

Pin Name Description/function
1 +UB 12 - 57.6 V DC
2 GND
3 U_OUT U (BLDC)
4 V_OUT V (BLDC)
5 W_OUT W (BLDC)
6 GND
Note:
  • EMC: For a DC power supply line longer than 30 m or when using the motor on a DC bus, additional interference-suppression and protection measures are necessary.
  • ► An EMI filter is to be inserted in the DC supply line as close as possible to the controller/motor.
  • ► Long data or supply lines are to be routed through ferrites.

X2 – inputs and outputs

Connectors:

  • CPB3: Amphenol 10144518-063802LF
  • CPB6: Amphenol 10144518-063802LF
  • CPB15: Amphenol 10144518-062802LF
Note: Some pins are freely configurable and support alternative functions. You can find details in chapter Defining input and output assignments.
Pin Name Description/function
1 GND
2 GND
3 reserved not connected
4 ANA1 Analog input 1: 0…3.2 V
5 reserved not connected
6 ANA2 Analog input 2: 0…3.2 V
7 reserved not connected
8 Spare not connected
9 RS485_DE Driver Enable
10 reserved not connected
11 RS485_RE Receiver Enable
12 reserved not connected
13 RS485_RX Modbus RTU Rx
14 reserved not connected
15 RS485_TX Modbus RTU Tx
16 GND
17 GND
18 H1 Hall sensor 1
19 DIO11 General I/O
20 H2 Hall sensor 2
21 DIO13 General I/O
22 H3 Hall sensor 3
23 ENC1B Encoder 1, B
24 ENC1A Encoder 1, A
25 SSI1_MISO SSI encoder 1, Data IN
26 ENC1I Encoder 1, index
27 SSI1_CLK SSI encoder 1, clock
28 U_SPIMISO MISO pin for rotary switch
29 DIO14 General I/O
30 U_SPISCK SCK pin for rotary switch
31 reserved not connected
32 reserved not connected
28 U_SPINSS SH/LDpin for rotary switch
34 reserved not connected
35 VBUS USB VBUS (power supply)
36 DP USB DP (Data+)
37 GND
38 DM USB DM (Data-)
39 DIO1 General I/O
40 GND
41 DIO3 General I/O
42 DIO2 General I/O
43 DIO5 General I/O
44 DIO4 General I/O
45 DIO7 General I/O
46 DIO6 General I/O
47 DIO9 General I/O
48 BRAKE Control of the external brake
49 GND
50 DIO10 General I/O
51 uC Reset System function, reserved
52 Ballast For controlling the external ballast circuit
53 uC Supply

Voltage supply 3.3 V

Must be provided by motherboard, limits: 3.2…3.4 V DC, min. 140 mA

54 uC Supply

Voltage supply 3.3 V

Must be provided by motherboard, limits: 3.2…3.4 V DC, min. 140 mA

55 Driver Supply

Voltage supply 10.5 V

Must be provided by motherboard, limits: 9.6…14 V DC, min. 70 mA

56 DIO12 General I/O
57 Ub_Logic Optional external logic supply, 12…30 V DC
58 Spare not connected
59 GND
60 GND
Note:
  • For the digital inputs, the switch-on threshold is 1.79 V and the switch-off threshold is 1.11 V (depending on the power supply at pins 53/54, typical values @3.3 V). The maximum sampling frequency is 1 MHz. If the I/O pins are used as output (see Defining input and output assignments), the maximum admissible current is approx. 10 mA at 3.3 V DC.
Tip: You can find information on the design of your motherboard in chapter Hardware installation.
▶   next

Contents